Home > Products >POE Splitter



•Bandwidth: 10/100/1000M
•Input Voltage: 37-57V
•Input port: Supports (No.4&5 and 7&8 cables supply power) and End-Span (No.1&2 and 3&6 cables supply power) connections.
•Two switchable output Voltages: 12V/24V
•Max output current: 2.0A (for output Voltage is 12V),1.0A(for output Voltage is 24V)
•Standard: Supports IEEE802.3af/at
•Isolation protection: Using the transformer for isolation design, more stable, more secure
•Protection function: Overheating protection, Short circuit protection, overvoltage and overload protection

  • Details
  • Specifications
  • Wiring Diagram
  • Download

FS-PD2001-GM is a kind of PD Splitter (also called POE Splitter), supports IEEE802.3af/at standard; supplies power and transmits data to devices which do not support POE power supply (such as IP camera); The product uses the transformer for isolation design, which gives you more stable, more secure and Well-protects the powered products ,Bandwidth is 10/100/1000M. Mid-Span (No.4&5and 7&8 cables supply power) and End-Span (No.1&2 and 3&6 cables supply power) connections are well supported. The product has two switchable Output voltages: one is 12V, maximum current is 2.0A, the other is 24V, and maximum current is 1.0A. Some HD digital cameras do not have POE module which leads to the inconvenience and difficulty on installation. However, this device can solve the problem of wiring. Connect POE switch with PD Splitter, people can realize the power supply and data transmission of IP camera directly and timely.


Installation steps

1. Before installation, please check the following equipments and accessories, if there are any missing, please contact with your supplier.

1). 1pc FS-PD1001-EN10 device

2). 1pc user manual

2. Please install as below steps

1) Before installation, please turn off the power of all signal sources and the monitor in case of the damage to transmission device.

2) Use network cables to connect POE power supply device and RJ45 port of PD splitter

3) Connect DC connectors and RJ45 port with right powered device.

4) Check weather installation is correct and the device undamaged. Before power on POE device, make sure that all connections are reliable.



Such as equipment malfunction, according to the following way

1) Confirm whether equipment is installed as the manufacturer's installation requirements;

2) Confirm whether RJ45 cable contacted well, make sure no break, whether line order production complies with the EIA/TIA568A or 568B international standards;

3) Confirm the working power of device is less than PD Splitter's max output power 12W.

4) Confirm whether POE device can work normally. Use normal PD device to test if the PoE power supply works.

5) Use a set of normal work FS-PD1001-EN10 device to replace the broken device, by which to examine whether the equipment damage.

6) If still cannot troubleshooting, please contact with the manufacturer.


Making methods of RJ45 connector

Required tools: wire crimpers, network cable tester.

1) The wire sequence of RJ45l connector must complies with international standard of EIA/TIA 568A or EIA/TIA 568B.

2) Strip about 2cm's of insulating jacket to let 4 pairs UTP can be seen.

3) Separate 4 pairs UTP cable, and try to straighten each pair.

4) Arrange 8 cables with correct line sequence of EIA/TIA 568A or EIA/TIA 568B.

5) Cut thread residue and leave 1.5cm wire which exposed outside the insulating layer, and ensure 8 wires are straight and neat.

6) Put 8 wires in RJ 45 connector, then press with wire crimpers.

7) Repeat above five steps , make the other side of UTP cable; Then using the cable tester to test whether the cat5e/6 works  normally.


  • Accessories