|
8-Port 10/100Mbps IEEE 802.3af/at PoE Switch (End-Span PSE)
•Comply with IEEE802.3, IEEE802.3u, IEEE802.3af/at standards
•Support IEEE802.3x full-duplex flow control; support Auto MDI/MDIX
•8-Port support 48V-56VDC power to PoE powered devices
•Provide 15.4W or 30W power to powered devices
•110-watts PoE budget
•Built-in 53VDC/1.85A switching power supply
•Extra 2-Port 10/100Mbps UPLINK RJ-45
•PoE data & power transmission distance up to 100 meters
•Port based VLAN for Enhancing Security
•Backplane Bandwidth: 2.0Gbps
•Excellent anti-thunder, anti-static and anti-interference ability
•Surge Protection: 4KV
•Easy and convenient to use, plug & play, no need to configure
•Galvanized housing for stable and durable working life
1 Downlink Port: Transfer data from other lP devices to the switch
2 Power Indicator: Red Light on: with power Light off: no powerUplink Port: Transfer data from PoE ports to other devices (NVR/Switch/ADSL)
3 Link/Act Indicator: Green Light on: Indicates that this port is connected
Blinks: Indicates that this port is sending/receiving Ethernet frames
Light off: Indicates that this port is sending/receiving Ethernet frames
4 Power Indicator: Green Light on: Power on Light off: Power off
5 VLAN Indicator: Green Light on: VLAN and extension mode starts
Light off: VLAN and extension function stops Light off: Power off
1 Ground Connection
2 Input: AC 100~240V
At present, applications of Ethernet switch are very wide. To satisfy the needs of various customers, it is urgent for network services to solve the problems of broadcast domains, bandwidth and security, so a new kind of technology of VLAN emerged.
Each DOWNLINK RJ-45 port and UPLINK RJ-45 port form a separate workstation respectively. In the same VLAN workstation, regardless of which switch they are actually connected to, the communication between them is as if they were on a separate switch. Broadcasts in the same VLAN can only be heard by members of the VLAN, but not in other VLANs, which can control the generation of unwanted broadcast storms. At the same time, if there is no routing, different VLANs cannot communicate with each other, which increases the security of different departments in the enterprise network.
When the VLAN mode is enabled, the data cannot be forwarded among DOWNLINK RJ-45 ports, but DOWNLINK ports and UPLINK RJ-45 port can communicate with each other. The bandwidth of DOWNLINK RJ-45 port is forced to 10Mbps mode to adapt to long distance transmission of max 250 meters. The bandwidth of UPLINK RJ-45 port is 1000Mbps, which keeps a cascade connection with another switch or NVR.
Note:
1. After you turned on VLAN button, please press reset button or reboot the device, then VLAN mode is enabled.
2. The maximum extended distance up to 250 meters.The actual extended distance will vary according to the quality of the cable, specific camera and on-site environment.
1. Cat5e, Cat6, or Cat7 cable
2. RJ-45 connectors
3. Crimping tool
4. Wire stripper or Knife
1) We recommend stripping at least half an inch of the cable to expose the inner wires.
2) Separate the wires within the cable after the network cable jacket has been removed so that they can be put into the RJ-45 connector.
3) The CAT5 twisted-pair cable consists of four twisted wires, each color coded; 8 wires must be correctly lined as the standards of EIA/TIA 568A or EIA/TIA 568B.
4) Cut thread residue and leave 1.5cm wire exposed outside the insulating layer and ensure 8 wires are straighten and neat.
5) Place the cable into the RJ-45 connector and then use the crimping tool to attach the connector.
6) Repeat above steps for the other end of the cable; the wire sequence of both ends of the cable is suggested to be identical.
7) Make sure to test the cables before installing them once both ends of the cable have been completed.
Note:
1. All RJ-45 Ports of this device support Auto MDI/MDIX, so the different wire sequence of both ends of the cable is allowed.
2. Up to two units can be cascaded.
Package Contents
1) FS-S0008EP-2E: 1pc 2) AC cable: 1pc
3) Manual: 1pc
Step 1: Begin with all input/output devices turned off and power cables are removed.
Step 2: Connect RJ-45 port of PoE cameras with Downlink RJ-45 port of PoE switches over standard Cat 5e/6 cables.
Step 3: Connect Uplink port of PoE switches with RJ-45 port of NVR or computer or other devices over standard Cat 5e/6 cables.
Step 4: Connect AC power cable with PoE switches.
Step 5: Make sure above connection is properly finished, then turn on the power.
|
Model |
FS-S0008EP-2E |
|
|
Product Name |
8-Port 10/100Mbps IEEE 802.3af/at PoE Switch (End-Span PSE) |
|
|
Power Supply |
Power Supply Mode |
AC Power Supply |
|
Voltage Range |
AC100~240V |
|
|
Power Consumption |
The device <5W PoE power supply ≤110W |
|
|
Network Port Parameter |
Network Port |
Ethernet Downlink RJ-45 Port: 8*10/100Mbps Uplink RJ-45 Port: 2*10/100Mbps |
|
Transmission Distance |
1~8 Ethernet Downlink RJ-45 Port: 100m Uplink RJ-45 Port: 100m |
|
|
Transmission Medium |
1~8 Ethernet Downlink RJ-45 Port: Cat5e/6 standard cable Uplink RJ-45 Port: Cat5e/6 standard cable |
|
|
PoE Standards |
IEEE802.3af/at |
|
|
PoE Power Supply Mode |
End-span method |
|
|
PoE Power Supply Wattage |
Each port ≤30W Whole device≤110W |
|
|
Network Switch Specification |
Network Standards |
IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX/FX, IEEE802.3az |
|
Swap Mode |
Store-and-forward |
|
|
Data-Caching Mechanism |
1.5Mb |
|
|
MAC Address List |
2K |
|
|
Backplane Bandwidth |
2.0Gbps |
|
|
Forwarding Capacity |
1.48Mpps |
|
|
Indicator/Button |
Power Indicator |
Green LED on: power on |
|
Fast Ethernet Uplink Port |
LED on: link up, off: link down, blinks: data transferring |
|
|
PoE Network Port Indicator |
LED on: link up,1~8 port indicators blink while data transferring |
|
|
Reset Button |
Press the reset button to turn on indicator (green) and the device restarts. |
|
|
VLAN Button |
Turn on VLAN button: VLAN and extension function starts Turn off VLAN button: VLAN and extension function stops |
|
|
Protection Level |
Surge Protection |
2KV (common mode),10/700us IEC61000-4-5 500V (differential mode),10/700us IEC610000-4-5 |
|
Electrostatic Protection |
Contact Discharge: ±2KV Air Discharge: ±2KV Standard: IEC61000-4-2 |
|
|
Reliability |
Mean time between failures (MTBF) |
＞50000h |
|
Mechanical |
Dimensions (L*W*H) |
200mmx118mmx45mm |
|
Housing |
Galvanized |
|
|
Body Color |
Black |
|
|
Net Weight |
780g |
|
|
Environmental
|
Operating Temperature |
0℃~55℃ |
|
Storage Temperature |
-40℃~85℃ |
|
|
Relative Humidity |
0~95% (non-condensing) |
|
• Security Monitoring System
• Multimedia Network Teaching System
• Medical Monitoring Display System
• Industrial Automation Control System
• Banking, securities, financial information display system
• Remote Network Server Monitoring
• Department Store Security
• Casino Security
• Hospitals, Airports and banks
• School Campuses
Copyright © 2019 Shenzhen Folksafe Technology Co., Ltd. All Rights Reserved | Designed by Joymagic
